DO-ALL #18 is shipped as a concentrate to be diluted as needed to meet multitudes of cleaning demands. We recommend that you start with the recommended levels and adjust up or down as needed to get the results you need. Remember, agitation is the key to using this product, not adding more chemical. Only add more after scrubbing is no longer effective.
Apply liberally with sprayer, automatic scrubber, mop, cloth or sponge, allow to stand a few minutes .
For large outdoor areas, spray off with hose or pressure washer.
For small areas, wipe with wrung out cloth or sponge. Surfaces that food may contact should be rinsed with potable water, otherwise rinsing is not usually required.
As a Dispersant:
DO-ALL #18 can be applied by hand, by boat and by air. Instructions can be found here:
DISPERSANT
Beach Cleanup
DO-ALL #18 can be used on beaches, dock pilings, rocks, Instructions can be found here:
Beach Clean-up
Oil Spills at Sea
DO-ALL #18 is safe to use on the open waters. Instructions can be found here:
Oil Spills
Offshore Oil Rigs
DO-ALL #18 is safe for use from top to bottom. Instructions can be found here:
Oil Rigs
Boats and Ships
Bilge Cleaning - dilute 1:10 parts of either fresh or salt water and agitate by roll of the vessel or by coarse water spray.
Pressure Washing - dilute 1:30-60 parts water.
Boats in the Water and Upholstery - dilute 1:20 parts water to remove contaminants, oil, grease, tar, etc. Rinse thoroughly with water.
Decks, Cabins, and Motor Compartments - dilute 1:10 and spray on. Allow 1-3 minutes to thoroughly saturate heavy deposits and then spray with clean water to remove residue. Scrubbing with a brush will enhance the process and may be necessary for heavier deposits.
Boat Hulls and Motor Drives - dilute 1:1 or full strength on a soft bristle brush and agitate. Follow with a rinse of 1:30-60.
Engines - dilute 1:3-5 and allow soaking for 15-20 minutes on very heavy soil. Follow with 1:30-60 rinse or straight water to remove all residues, depending on soil level.
Sump Cleaning - circulate 1:8 parts water for 30 minutes. Rinse with clean water.
Boiler Tank Cleaning - dilute 1:100 for corrosion and scale inhibition on an empty tank. Not for addition to boiler water.
Household / Restaurants (per gallon of water)
Light soil and damp mopping - 2 oz.
Greasy, heavy soils - 12 oz.
Air Conditioner coils - 10 oz.
Air Filters - 8 oz.
Exhaust Fans - 12 oz.
Food Processing equipment - 8 oz. (follow with a clear water rinse)
Light Fixtures - 6 oz.
Machine tools - 8 oz.
Ovens - 1:1 or full strength (best results, preheat oven to 200° before applying) wipe off after 20-30 minutes.
Refrigerators - 6 oz.
Painted walls and trim - 4 oz.
Plastics - 4 oz.
Soap scum - 8 oz.
Spot Remover - use full strength on the spot, let stand then wash, rinse or sponge as usual
Clothes, laundry - use 1/2 oz of DO-ALL #18 to every 4 gallons of water or 1 cup per washer load.
Steel files & Lockers - 2 oz.
Wash room fixtures - 4 oz.
DO-ALL #18 quickly emulsifies, dissolves, bio-degrades animal fats, vegetable oils, petroleum greases and oils.
Industrial / Commercial
Floor scrubbing machines - 1:30-60 parts water
Auto/Truck/Airplane washing - 1:30 parts water (may remove wax). For heavy soil, scrub prior to rinsing.
Radiator Cleaning - pour 12 oz of DO-ALL #18 into radiator and run. Use for one week then drain and flush radiator with fresh water.
Parts Washer - 1:15 parts water. Soak 20 minutes or hand wash using a bristle brush to clean caked on grease. Rinse with fresh water.
Ultrasonic Cleaning - 1:100 parts water
Hand Cleaning - can be used up to full strength, rinse with water
Engines - dilute 1:3-5 and allow soaking for 15-20 minutes on very heavy soil. Follow with 1:30-60 rinse or straight water to remove all residues, depending on soil level.
Equipment Cleaning - 1 part DO-ALL #18 to 10-50 parts water. Apply solution on all surfaces that have been contaminated with oil, grease, tar, soot, etc. Safe to use on all surfaces except aluminum, which must have a dilution of at least 1:20 before application. Let application work for 1-3 minutes. Heavy build-up should be agitated wit a cloth or bristle brush.
Plastic Cleaning - 1:30 parts water, will not crack or craze plastics
Spot Remover - use full strength on the spot, let stand then wash, rinse or sponge as usual
Rain Suit Cleaning - 1:1 with water, scrub with a medium bristle brush until all oil, grease and tar are removed. Dilute 1:20 to remove remaining light residue, if any. Rinse thoroughly and allow to air dry.
Rubber Boots and Work Shoes - 1:40 parts water. Dip brush into dilution and scrub vigorously and rinse with clean water. Also works for rubber gloves.
Clothes, industrial laundry - use 4 oz. DO-ALL #18 per 50 lb load. If articles are lightly soiled, make a dilution of 1:20 and spray directly on soiled area. Allow to stand 1-2 minutes, rub soiled area lightly then place into washing machine. For heavily soiled pieces, place articles into a bath of DO-ALL #18 @ 1:20, allow to stand for 5-7 minutes and place directly into the washing machine. If light residue or light stains remain after the first washing, simply re-wash to remove the residue.
Spray Washing - 1:30 parts water. An airless type gun or non-atomizing type spray gun is mandatory to prevent solution from foaming excessively. Hot water (107° F) increases effectiveness.
Airplanes and Airports
Stretch your maintence dollar with our recomendations here:
Aviation
